SOLAR POWER CALCULATOR

Solar Inverter Size Calculator

Estimate the inverter capacity your solar system needs. Calculate continuous power requirements, account for motor starting surges, and estimate the DC current drawn from your battery.

Enter Your Electrical Loads

Enter the appliances expected to operate at the same time. Use their running power ratings, not their daily energy consumption.

Watts
Add the running wattage of all appliances that may operate simultaneously.
Use 1.00 for a purely resistive load. For mixed household loads, an estimate such as 0.90 may be useful if actual appliance data is unavailable.
%
Adds extra continuous capacity for practical operating headroom and future load variation.

Motor and Starting Surge

Watts
Enter the running watts of the largest motor, pump, refrigerator compressor or similar appliance. Enter 0 if there is no significant motor load. This load is assumed to be included in the total.
Example: 3 means the motor may briefly require three times its running power. Use manufacturer starting-current data whenever available.

Battery and Inverter Settings

%
Used to estimate battery-side DC power and current.
Select the nominal DC voltage of your battery bank. This affects the estimated DC current, not the AC inverter output rating.

How to Use This Calculator

  1. List appliances that may run at the same time.
  2. Add their running wattage to obtain the total load.
  3. Enter the power factor if known.
  4. Add the running watts of the largest motor.
  5. Estimate its starting surge multiplier.
  6. Enter the battery voltage and inverter efficiency.
  7. Calculate the suggested inverter capacity.

Example Appliance Loads

These are illustrative running-power estimates. Actual appliance ratings vary by model.

Appliance Example watts
LED lighting100 W
Refrigerator200 W
Television120 W
Laptop80 W
Water pump750 W
Microwave1,000 W
Washing machine500 W

Important Sizing Tip

Do not select an inverter using only the total wattage of your solar panels. Inverter selection must account for the AC loads, battery or grid configuration, voltage compatibility, surge capability and installation requirements.

Always check the inverter manufacturer's continuous output, surge duration, power factor limits and temperature derating specifications.

How Is Solar Inverter Size Calculated?

An inverter converts DC electricity from solar batteries or solar panels into AC electricity for appliances. Its continuous output rating must be sufficient for the real power and apparent power demanded by the connected loads.

1. Calculate apparent power

Apparent Power (VA) = Running Load (W) ÷ Power Factor

Power factor represents the relationship between real power measured in watts and apparent power measured in volt-amperes. The inverter must be compatible with the power factor of the loads.

2. Add a sizing margin

Required Continuous VA = Apparent Power × (1 + Margin ÷ 100)

The margin provides additional capacity for normal operating variation. It does not replace a proper assessment of motor starting requirements or manufacturer limits.

3. Estimate motor starting surge

Surge Watts = Other Running Loads + (Motor Watts × Surge Multiplier)

The calculator converts this estimated surge load into an approximate VA requirement using the entered power factor and sizing margin. Actual starting current and power factor can differ substantially from running conditions.

4. Estimate battery-side DC current

DC Power = AC Running Load ÷ Inverter Efficiency
DC Current (A) = DC Power (W) ÷ Battery Voltage (V)

This is an approximate running-current estimate. Actual battery current changes with load, battery voltage, inverter losses and operating conditions.

What Size Solar Inverter Do You Need?

The right inverter depends on the appliances you intend to operate simultaneously, their power factor and their starting requirements. A small cabin with lighting and electronics may need a much smaller inverter than a home operating pumps, refrigerators, kitchen appliances and other large loads.

For example, if your simultaneous running load is 3,000 W, your power factor is 0.90 and your sizing margin is 25%:

3,000 ÷ 0.90 = 3,333 VA
3,333 × 1.25 = 4,167 VA

A standard inverter rating above this continuous requirement would be considered. You must then separately verify that its surge rating can start the largest motor while other appliances are operating.

Choosing Between Inverter Types

Off-grid inverter

An off-grid inverter supplies AC power from a battery-based system without depending on the utility grid. Battery voltage, battery discharge limits and solar charging capacity are important design considerations.

Hybrid inverter

A hybrid inverter coordinates solar panels, batteries and, depending on the model, grid electricity. Check its battery compatibility and its separate grid-connected and backup output specifications.

Grid-tied inverter

A grid-tied inverter synchronizes solar electricity with the utility grid. Its sizing is generally based on PV array characteristics, grid connection requirements and permitted export capacity, rather than simply the household appliance load calculated on this page.

Pure sine wave inverter

Pure sine wave output is generally the preferred choice for sensitive electronics, appliances and equipment with motors. Confirm that the output voltage and frequency match the connected equipment.

Frequently Asked Questions

1. What size inverter do I need for a 5 kW solar system?

A 5 kW solar panel array does not automatically require a 5 kW inverter. The appropriate inverter depends on the inverter's permitted DC input, the panel array design, grid rules, battery configuration and expected AC loads.

2. Is a 5 kW inverter enough for a house?

It may be sufficient for a home with moderate simultaneous loads. However, electric heating, cooking equipment, pumps and other large appliances can require more capacity. Calculate the loads that will operate together.

3. Why does an inverter need a surge rating?

Some appliances, particularly motors and compressors, briefly draw much more current when starting than when running. The inverter must be able to supply this temporary demand for the duration specified by its manufacturer.

4. What is the difference between watts and VA?

Watts measure real electrical power. Volt-amperes measure apparent power. For AC loads, the relationship depends on power factor: watts equal VA multiplied by power factor.

5. Does a larger inverter always mean a better solar system?

No. An oversized inverter may increase cost and may operate inefficiently at very low loads. Select a suitable model based on the load profile, solar array, battery system and manufacturer's operating requirements.

6. Can I use this calculator for a grid-tied inverter?

The calculator provides an estimate based on appliance loads. Grid-tied inverter selection also requires PV array voltage and current checks, grid compatibility and local utility requirements. Use the manufacturer's design tools for final selection.

7. How do I know if my battery can support the inverter?

Check the battery's continuous and peak discharge current, voltage range, BMS limits and permitted operating conditions. The battery bank and DC protection must support the inverter's actual current demand.

Disclaimer: This calculator provides preliminary educational estimates, not professional electrical design advice. Final inverter selection must account for appliance starting characteristics, inverter temperature derating, continuous and peak ratings, battery discharge limits, DC protection, wiring, grounding, local electrical codes and grid requirements. Consult a qualified solar installer or electrician before purchasing or installing equipment.